Discount Pool Zone
        Swimming Pool Supplies & Parts


Shop By Category:

Home
Pool Cleaners
Complete Filters
Replacement Filters
     Cartridges & DE Grids
Pumps
Motors
Timers
Lights
Pool Accessories
Test Kits
Valves (Multiport)
Chlorinators
Salt Generator
Pump/Skimmer Baskets
Pool Chemicals
Parts
     Pump/Filter
   Pool Cleaners
      Pool Vac/Navigator
      Baracuda
      Sta-Rite Great White
   O-Rings
        Pool Pump Motors                        

     A.O. Smith Replacement Motors

Sta-Rite
Max-E-Glas Pump

Up-Rated
    Square Flange
     RPM 3450
    Frame 48Y
Pump Model
Number
 AO Smith
Replacement 		HP
 Volts
 Max Amps
 Service Factor
 Price
PEA5D
PEA6D
 USQ1072
 3/4
 115/230
 11.8/5.9
 1.27
 $143.99
PEA5E
PEA6E		 USQ1102
 1
 115/230
 14.8/7.4
 1.25
 $153.99
PEA5F
PEA6F		 USQ1152
 1-1/12
 115/230
 19.2/9.6
 1.1
 $163.99
PEA5G
PEA6G		 USQ1202
 2
 208-230
 10.4
 1.1
 $213.99

Common Seals and Orings that may need to be replaced when replacing the pump motor

Shaft Seal PS-100 (Pre 1998 with Copper insert - If Copper insert has been removed you will need PS-200)
$8.99

If you have a Ozone or Salt Pool we recommend Shaft Seal PS-3866 vs the PS-100 
$12.99

Shaft Seal PS-200
$8.99

If you have a Ozone or Salt Pool we recommend Shaft Seal PS-3867 vs the PS-200 
$12.99

Seal Plate O-ring   U9228A  (Aladdin Replacement O-ring O-240)
$8.99
Diffuser O-ring   U9226  (Aladdin Replacement O-ring O-49)
$3.99
Motor Failure:

Shaft seal failure is the major cause of motor failure. This allows moisture to go back to the motor causing corrosion and much more. One of the causes of a shaft seal going bad is the result of the pump running dry which heats up all the parts inside the pump causing damage. It's always best to replace the shaft seal when installing a new motor. If the motor fails due to water damage it can void the manufactures warranty.

All A.O. Smith Motors carry a one year manufacturers warranty (Water damage is not covered).

ATTENTION: Improperly wiring a motor will cause irreversible damage. If the motor runs slowly then trips out, it is incorrectly wired. Please carefully read the motor name plate regarding the connections. 115/230 volt motors are shipped from the factory connected for 230 volts. A motor connected for 115 volts that has 230 volts applied will burn up immediately. A motor connected for 230 volts that has 115 volts applied will run slowly and trip out. If the wires moved on the connection board are not replaced on the proper terminals, the result will be a slow running motor that overheats and trips out. These motors have automatic overload protection, which means the motor will not run again until it cools down. If you are experiencing problems, please recheck the connections to insure you have the motor properly wired for the incoming voltage. These motors have been test run at the factory, and they very rarely have problems. Problems are almost always related to improper wiring or other installation issues. Please be sure that you are ordering the correct motor and that follow all installation instructions carefully.




Sta-Rite Max-E-Glas Pump



                 

Policies           Shipping          Contact
Discount Pool Zone, LLC
611 Overhill Dr
Brandon, FL 33511
Local 813.689.5800
Toll Free 877.222.6122

Your Discount Swimming Pool Supplies Headquarters